Envirosun TS Plus Solar

Envirosun TS Plus solar hot water systems

Envirosun THX Plus solar hot water heaters

FACT - The Envirosun TS Plus solar hot water heater is one of the highest preforming and awarded solar hot water systems in Australia

The Envirosun TS Plus 300 litre, open circuit 2 panel thermosyphon solar hot water heater is a superior made hot water unit, with the roof mounted storage cylinder that is manufactured in Holland from a very high grade 444 Stainless Steel for a longer life expectancy, this is imported to Australia as a bare tank and is all assembled in Victoria. The Envirosun TS Plus comes with 2 high solar absorption solar collector panels. These solar panels have one of the higher solargain / heat absorption rate in Australia over 20% higher than most other brands for solar hot water systems on the market. This reflects in our STC rating Envirosun TS Plus suitable for nearly every area in Australia. We also have a range of Envirosun solar panels for far north Queensland, the Northern Territory and other areas closer to the equator where solar adsorption rates are extreme, we also have engineered cyclone frames for the north Queensland coast line and Darwin and even flat roof pitch frames to elevate the systems when installing on roofs below the recommended pitch needed for solar gain

We also have the Envirosun THX Plus, a closed circuit glycol solar hot water system, this is suitable for high frost prone and colder regions.  A glycol solar hot water heater uses a fluid (the Gylcol) to transfer the heat to the storage tank, this is a anti freeze / anti boil product.  Undoubtedly the Envirosun THX glycol solar is the best solar hot water system of its type in Australia, once again we have a quality stainless steel storage tank and with the high efficient solar panels. The Envirosun THX Plus glycol solar hot water system like the Envirosun TS Plus is government tested and has a higher STC’s rating than any other brand, that there stands for itself

Did I mention that Envirosun thermosiphon solar hot water systems are approximately 1/2 the weight as other mild steel enamel lined roof top solar hot water systems

Envirosun TS Plus solar hot water system come with 7 years warranty on the tank and solar panels

Envirosun’s Thermosiphon System (the TS Plus) is one of the most advanced solar hot water systems available in today’s market, offering a extremely high efficiency rate and a cost effective solution for most domestic homes. The Envirosun hot water storage cylinder and the solar collector panels are roof-mounted together as one seamless combined unit. Water is heated in the flat plate solar collector, and natural convection of hot water rising moves the water through the system into an insulated storage tank located above the solar panels on the right hand side as cooler water from the tank falls from the left into the lowest part of the solar panels, minimising any energy required.  This design principle has been in the roof mounted tank solar water heaters since the development of solar water heating and the Envirosun TS Plus outperforms other brands of systems with offers a superior level of efficiency and a economical solar hot water heating outlay. The clever design and engineering of the Envirosun TS Plus Thermosiphon System utilises the strongest of materials and state-of-the-art tank protection valves and systems to ensure a long operating life in all environments, from extreme heat on summer days to the near freezing winter nights are also not a problem. The Envirosun THX Plus is our closed circuit glycol solar and is suitable for areas which experience below zero winter night temperatures,  common frosts and in some cases snow. It is also  a better choice in some areas where the water quality is bit a below average.  This system uses the very efficient heat transferring properties of a special anti-freeze fluid, Glycol to transfer the absorbed energy to heat the water indirectly. In the Envirosun THX Plus solar hot water system, the water within the storage tank does not flow through the solar collectors, instead a glycol fluid is circulating from the solar panels through a “jacket” which is wrapped around the hot water storage tank. The Envirosun THX solar also is awarded higher STC’s than competitor brands of this closed circuit thermosiphon type

 The latest cutting edge technology and the cumulative advancements of Envirosun’s 25 years industry experience combine to offer the ultimate in durability, reliability and affordability.

Envirosun is a Australian owned company that is operated with true family values and integrity,  with the highest level of quality control that makes the Envirosun TS Plus thermosyphon stainless steel solar hot water heater choice a smart one, not only financially but environmental and for a sustainable future Australia

Contact us for more details on how we can supply you with this quality affordable solar hot water system. 

Better than solahart Envirosun is Australia's premium solar hot water range
Frost protected solar hot water systems, Envirosun TS Plus closed circuit
Below is a bit of technical talk about the Envirosun TS Plus solar hot water heater range

The Storage tank

Envirosun pioneered and mastered the use of Type 444 ferritic stainless steel in the construction of our TS Plus solar hot water range

Envirosun solar water heater TS Plus

Compared with traditional austenitic stainless steel (such as Type 316L and 304L) ferritic stainless steels offer major performance advantages. In particular, Type 444 out-lasts Type 316L when it comes to resisting localized corrosion or pitting attack at elevated water temperatures.

Generally, Type 444 is a highly durable and trouble-free material that offers significant live cycle cost advantages. Stainless steels derive their corrosion resistant properties through the inclusion of stainless steel. However the key to the enhanced performance of this Type 444 is the addition of molybdenum and chromium as further alloying elements (traditional austenitic grades incorporate nickel). During the final stage of the factory guarantee period you should arrange for an end-of-warranty service to be carried out. These quality European made 444 stainless steel cylinders have the final assembly here in Australia

The Insulation

Keeping the heat on the inside of a hot water system storage tank is the major aspect of saving energy and operating costs, and polyurethane insulation systems are the best way of doing this. That's why Envirosun use this on all our solar hot water systems

Envirosun energy efficient solar hot water systems

Polyurethane is formed through the chemical reaction of two liquids with the mixture then injected into the contained space around the hot water storage tank and outer casing.  As the mixture is exposed to air, it expands to up to 10 times its liquid volume. In so doing it fills all of the contained space including the smallest of crevices. As the mixture dries it hardens to form a closed-cell structure that is a rigid and impermeable structure. Compared to fibreglass insulation that allows air to permeate, polyurethane is airtight. The resulting insulating barrier works at three levels: the gases trapped in the cells resist conductive heat losses; the air-tight structure prevents convective heat loss otherwise caused by the flow of warm air to the cooler surrounds; and condensation heat loss, normally caused as warm air is introduced to cold air, are avoided.

The solar hot water cylinders of all Envirosun storage tanks are encased within a polyurethane foam insulation system. The polyurethane mixture is pressure injected into the space between the cylinder and the external sheet metal casing.

The combination of metal and foam contributes to structural rigidity and is the basis of its excellent heat retention properties. Heat retention = more hot water for a longer period of time and that equates to money and energy cost savings

The Solar Panels

Envirosun solar panels for water heateing
Envirosun solar panels made from copper
Envirosun solar hot water panels

The absorber plates in our solar collectors are designed to absorb more of the sun’s energy and radiate less back to the environment as heat.

To achieve this they undergo a two-stage electroplating process. They are first plated with a layer of bright nickel and then re-treated with an over-coat of black chrome. This creates a ‘spectrally-selective surface’ that absorbs more solar radiation and re-emits less thermal energy. The underlying mechanisms are relatively simple. In the short wavelength part of the spectrum, the absorber behaves like a black surface and soaks up most of the sun’s energy. In the long wave length part of the spectrum, the absorber behaves like a silver surface and re-radiates little of its heat.

Envirosun’s black chrome absorbers plates have the highest efficiency solar selective coating available and they deliver performance gains about 20% above those available from such  non-selective treatments.

Envirosun solar hot water panels are secured inside high grade coated aluminium frames to reduce any corrosive materials on your roof

Our collectors are fitted with solar glass that is highly translucent and very strong.

It’s intended as maximising the amount of solar energy that is captured by the collector absorber plates (panels) while protecting them from impact damage. To explain, this, it’s first necessary to understand how a solar collector uses the ‘greenhouse-effect’ phenomenon to heat water.

As the sun’s rays fall on the glass cover are a form of short wavelength radiation. Most of the solar radiation passes through the glass but some is reflected or absorbed. The transmitted portion of solar radiation that reaches the black copper absorber plate, heats it and the water that is contained inside the pipework. The hot absorber also re-radiates thermal energy (a form of long wavelength radiation) which, in the absence of a cover, would escape and allow the plate to cool. The glass cover, however, acts as a reflector of the long wavelength radiation and bounces it back to the absorber, thereby containing the heat. Glass that has higher iron levels absorbs more solar radiation and allows less to reach the absorber plates. Low-iron glass can transmit about 91% of the incident solar radiation. Envirosun solar glass is produced with very low levels of iron impurities. Envirosun solar glass is also tempered using a heat-treatment process.

Boosters For Bad Weather

Running out of hot water is not a problem with electric and gas boosters available ensuring hot water is always

Envirosun solar hot water systems are equipped with either electric boosters that can also have Natural or LPG gas boosters added to ensure that there’s plenty of hot-water available during the worst weather or when the demand for hot water is high. Electric elements are fitted inside our storage tanks and the gas instantaneous heaters can be installed in-line from the outlet of our systems. Both options are designed to maximise the amount of solar energy that can be collected and utilise the auxiliary in a ‘back-up’ or ‘booster’ mode only.

Electric Boosters

Electric boosted systems are integrated arrangements that comprise a heating element immersed in the storage tank water, controlled by a thermostat and connected to a switched power-supply. Both the element and thermostat are positioned at the midpoint of the tank and the power-supply switch is conveniently located. With the power-supply on, if the temperature at the centre of the tank falls below 60°C, the thermostat ‘closes’ and the heating element operates. The element continues to operate until the mid-point of the tank rises to above 60°C. The location of the element and thermostat in an Envirosun system are designed to only allow the booster to only heat the water in the top half of the tank and to leave the bottom portion available for useful solar gain. Our solar hot water systems have the ability to heat water without direct sunlight to approximately 2 x the ambient air temperature, for instance if it is a overcast day and the outside temperature is 22 degC  for most of the day, your solar should be able to get the water to around 44 degC

Gas Boosters

Gas boosted systems involve a continuous-flow gas water heater that is mounted separate from the storage tank. The outlet from the solar hot water system is piped as the inlet to the gas heater. If the water reaches the gas heater at a temperature below 60°C, the gas supply is opened, the spark-ignition system fires, and the gas burner operates. If the inlet water temperature is above 60°C, the gas heater does not operate.

Envirosun systems use this pre-heater configuration to achieve higher solar contribution and significantly lower greenhouse gas emissions.

Envirosun solar hot water systems have a 7 year warranty
Envirosun TS plus solar hot water brochure
Envirosun TS Plus Brochure
Australian Hot Water Systems
Envirosun Solar hot water systems, Australia's best water heater
Click image to go to Envirosun AS solar hot water systems
Enviroheat heat pump hot water systems
Click image to go to Enviroheat heat pump hot water system

Up To 90% energy savings

Check out some of the comparisons here on different heat pump hot water heater brands and the Australian Government tested and allocated STC rating, the STC is a rated saving that a hot water system has been granted after testing and approved by the  Australian Clean Energy Regulator,  the number of STC’s that are issued refers to one megawatt hour (1 MWh) of avoided energy consumption over the heat pump hot water system’s deemed life expectancy

S =  R – T  where: S: STC count  R: Reference conventional system’s energy consumption (MWh over ten years) T: Tested system’s estimated energy consumption (MWh over ten years)

Here is a graph showing savings and ratings of STC assigned to Thermosyphon solar hot water systems and the approximate percentage of power saving  compared to a conventional electric water heater in zone 3 

Renewable Energy Target | Tindo Solar

Envirosun TSPlus TS300/40, receives 40 STC
Envirosun TS Plus saves approximately 40,000 kWh of energy 90%
Rinnai Prestige 300lt receives 39 STC
Rinnai S/S Solar hot water systems saves approx 39,000 kWh of energy 87%
Sun Rain 300lt 2P receives 35 STC
Sun Rain FPTS300-2P saves approximately 35,000 kWh of energy 79%
Solahart 302j Solar hot water system receives 28 STC
Solahart 302j saves approximately 28,000 kWh of energy 65%
Rheem 300 Hiline receives 28 STC
Rheem 300lr HiLine saves approximately 28,000 kWh of energy 65%

How does a Envirosun TS Plus solar hot water system work?

The solar hot water storage tank and panels are connected together and located on the roof structure, facing in a northerly direction.  Hot water has a natural fall and rise cycle, hot water rises and cold water falls to the lowest point, as the sun heats the water in the collector, it rises and then goes into a storage tank. 

Hot water rises naturally in the tank – this process is called thermo-siphoning, that’s why this type of solar water heaters are known as thermosyphon solar hot water systems and the Envirosun TS Plus model

The colder water at the bottom of the storage tank then travels into the lowest point of the solar collector panel and as it starts to heat up it rises in the solar panels to the highest point, then through a pipe to the storage tank. (shown in diagram)

The solar hot water panels are a sealed cased box with toughened glass face, a manifold of copper pipes and black powder coated copper absorption plates or fins to attract the heat and with the underside being fully insulated, traps the heat inside to give maximum solar gain and heat transfer to the water

This process is a continuous cycle and can save the average household over 80% of their hot water energy usage and related greenhouse gas emissions, not to mention the money that is saved with this type of solar hot water systems

Envirosun, how does a solar hot water system work?
Click here for more information on Envirosun TS Plus solar water heaters
Envirosun TS Plus solar hot water systems
Contact Us    Call Us